Harris Race Radios

Aaron Harris – 027 449 9654

Rex Harris – 021 682912

Aim MXP Strada

MXP Strada

BUY ONLINE

Aim MXP Strada

A wide range of data sources

Aim MXP Strada is the the evolution of MXP Strada which is a 6″ TFT color display with great visual impact. It is configurable to show lap times and all the info coming from the Engine Control Unit like analog/digital inputs, pre-defined math channels and optionally, the GPS08 Module.

Aim MXP Strada is available in two versions:

Aim MXP Versions

Freely configurable pages

You can define all the custom pages you wish, choosing among a wide library of page styles, defining which data to be shown, their end of scale and measure units. Swapping between pages can be managed pushing one or two push buttons.

MXS Strada High Contrast TFT display

High Contrast TFT Display

Aim MXP features a high contrast TFT display: its visual quality is always optimal as its ambient light sensor keeps the back light at the best brightness levels. The dash is of course available also in the “Street Icons” version (fuel, oil, water temp etc.)

MXS Strada High Contrast TFT display

Flexible alarms & custom street icons

The MXP features five configurable RGB alarm LED’s. You choose the conditions, you choose the colours.  Select a solid alarm or flashing one – and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. Select then the street icons you need among the wide list you will find in “Race Studio 3 – Icons Management” and set them up the way you prefer or according with your needs. Any of them is fully configurable and if this shouldn’t be enough, you will be able to upload and set up your own customised icons.

MXS Strada Flexible Alarms

Two Digital Outputs

MXP features two digital outputs. The two digital outputs (Dout) are LOW SIDE type (switch to ground): they can be configured in order  to be turned on/off depending on the value of the analog or digital inputs. They permit to automatically run external systems, i.e. to switch on/off additional lights, to activate/de-activate a cooling fan or circulation pumps, etc. when a certain event happens.

MXS Strada Two Digital Outputs

Camera inputs, also for mirror camera

Two analog camera inputs are available, to swap your display into a mirror camera, through pushbutton command or event management.

Camera inputs, also for mirror camera

Integrated shift light array

Choose from a host of advanced multicoloured RGB shift light patterns that can be customised as you like and also for each unique gear when required.

Camera inputs, also for mirror camera

Expand the system according to your needs

GPS Module

Thanks to GPS05 Module (included in the kit) and its GPS Manager software, you can immediately get laptimes and all data needed for engine tuning as well as for improving driving technique

Channel Expansion It permits to add 4 0-5Volt analog channels for pressure, temperature sensors and potentiometers. Two of these channels can be configured to receive digital inputs like wheel speed.

Channel Expansion
It permits to add 4 0-5Volt analog channels for pressure, temperature sensors and potentiometers. Two of these channels can be configured to receive digital inputs like wheel speed.

TC Hub
It adds 4 K thermocouples.

LCU-One Lambda Controller

Wide band Lambda controller LCU-One, with Bosch LSU 4.9 probe, providing all Air/Fuel data, lambda value and exhaust gas temperature, allows to perfectly tune the carburetion.

Memory Module
Thanks to the SD Card, Memory Module can record all your data in a file that can be downloaded on your PC for post-analysis. Memory Module, with 16Gb capability, can be connected via CAN-Bus to MXL2 and to all AiM loggers.

SmartyCam HD cameras
The on-board cameras that overlays on videos the data sampled by your logger.

MXP Strada Connection Examples

MXP Strada Connection Examples

CAN output

With the CAN Output you can send messages directly  to an existing CAN network in order to improve  the range of vehicle control possibilities.

MXP Strada Connection Examples

Race Studio 3

Race Studio 3 is the heart of your MXP Strada managing all your racing activities.

Configuration

With Race Studio 3 you can create, modify, delete, import and export configurations with all channels, ECU drivers, Math channels, Display Pages, Digital outputs, Alarms, Shift Lights and all the expansions you need. You will also be able to manage the map of all your racing tracks and compare two laps watching the video recorded by SmartyCam HD cameras.

Race Studio 3
RS3 Analysis

Analysis

With Race Studio 3 you can also analyse all data recorded by MXP Strada and downloaded to your PC: graphs, histograms and tables will help you study your performance, providing an objective support to avoid mistakes and improve performances.

A wide range of data sources

MXP Strada is the dash logger designed to acquire and display data coming from your ECU, the internal accelerometer and gyro, as well as from the GPS08 Module included in the kit, analog/digital inputs and predefined math channels. Performance and data acquired can also be incremented adding up to eight expansion modules. Its 7″ display makes it perfect for wide cockpits installation.

In The Box
  • Aim MXP Strada
  • USB cable
  • 14 pins standard wiring
  • 23 pins connector + contacts
  • software installation CD